Effect of Vertical Misfit on Screw Joint Stability of Implant-Supported Crowns

The passive fit between prosthesis and implant is a relevant factor for screw joint stability and treatment success. The aim of this study was to evaluate the influence of vertical misfit in abutment-implant interface on preload maintenance of retention screw of implant-supported crowns. The crowns were fabricated with different abutments and veneering materials and divided into 5 groups (n = 12): Gold UCLA abutments cast in gold alloy veneered with ceramic (Group I) and resin (Group II), UCLA abutments cast in titanium veneered with ceramic (Group III) and resin (Group IV), and zirconia abutments with ceramic veneering (Group V). The crowns were attached to implants by gold retention screws with 35-N cm insertion torque. Specimens were submitted to mechanical cycling up to 10⁶ cycles. Measurements of detorque and vertical misfit in abutment-implant interface were performed before and after mechanical cycling. ANOVA revealed statistically significant difference (P < 0.05) among groups for vertical misfit measured before and after mechanical cycling. The abutments cast in titanium exhibited the highest misfit values. Pearson correlation test did not demonstrate significant correlation (P > 0.05) between vertical misfit and detorque value. It was concluded that vertical misfit did not influence torque maintenance and the abutments cast in titanium exhibited the highest misfit values.     

Calcium dosing for the simultaneous control of biomass retention and the enhancement of fermentative biohydrogen production in an innovative fixed-film bioreactor

Biohydrogen (bioH₂) production via dark fermentation is an attractive approach to overcome the drawbacks of conventional hydrogen production methods and represents a preliminary alternative for the management of organic wastes. Fundamental studies are still required to enhance the performance of bioH₂ production systems, with emphasis on the development of novel reactor configurations. The anaerobic structured-bed reactor (ASTBR) is a recently developed configuration with great potential for bioH₂ production, although operating strategies are still required to minimize biomass washout in such systems. In this context, calcium dosing has been investigated as a strategy to enhance both biomass retention and bioH₂ production rates in the ASTBR. The present study employed varying COD/calcium ratios (4423, 2079, 1357, 1012, 884, and 632) in continuous experiments under mesophilic conditions (25 °C). Calcium dosing effectively enhanced biomass retention within the ASTBR, directly increasing the availability of metabolic energy for different metabolic pathways rather than cell synthesis. An optimal COD/calcium ratio of 1360 was mathematically estimated for bioH₂ production, which is consistent with the results obtained experimentally. The specific organic loading rate (SOLR) was better controlled at this ratio, indicating the establishment of balanced conditions in terms of substrate availability and biomass concentration. Conversely, bioH₂ production was severely impaired at COD/calcium values below and above the optimal range, most likely due to enhancement of the homoacetogenic pathway as a result of unbalanced conditions in the SOLR. Furthermore, biomass accumulation did not strongly affect the mean residence time of the ASTBR, facilitating its robust and enhanced solid retention.     

Identification of unbalance forces by metaheuristic search algorithms

This paper discusses the identification of parameters in rotary systems, namely, the unbalance magnitude, phase and position in the rotor system. These parameters can be identified using the measured orbits in the hydrodynamic bearings. The oil film forces are evaluated in the different positions of the orbit of the journal and are applied to the model of the shaft. The model, integrated in time domain, allows with an assumed unbalance, to simulate the orbits. The objective function is basically the difference between measured and simulated orbits, and its minimum corresponds to the identified unbalance amount, phase and position along the shaft. With respect to traditional model based identification procedures, this approach using oil film forces instead of oil film linearized stiffness and damping coefficients, and unfiltered orbits instead of 1X vibration components is suitable to deal with non-linear behaviour of the system.     

XRD Analysis of the Role of Cesium in Sodium‐Based Geopolymer

The purpose of this work was to study the role of cesium in sodium‐based geopolymer and its thermal stability for nuclear waste management. A series of mixed sodium and cesium geopolymer samples (Na_1?x Cs _x )₂O·Al₂O₃·SiO₂·12H₂O (referred to as (Na_{1? x} Cs _x )‐GP, where x = 0, 0.08, 0.15, 0.42, 1) have been prepared. All geopolymer samples were heated at 1100°C for 24 h. Pollucite (CsAlSi₂O₆) and feldspathoid (CsAlSiO₄) were crystallized from Cs‐GP. Nepheline (NaAlSiO₄) and a small amount of crystallized silica were obtained from Na‐GP. The other geopolymers (Na_{1? x} Cs _x )‐GP (x = 0.08, 0.15, 0.42) led to pollucite and nepheline main phases. Amorphous silica phase was observed in all the geopolymer samples with various amounts. Phase quantification and scanning electron microscope revealed that higher Cs concentrations in Na‐GP tend to decrease the amorphous phase while improving pollucite and nepheline phase quantification. The amorphous geopolymers have also been studied by pair distribution function analysis. Tetrahedral chains formed by T–O bonding (with T = Si, Al) were shown to be more tighten around Cs⁺ than around Na⁺. It led to shorter Cs–T bond than Na–T bond matching the higher solvation property of Na⁺. Furthermore, thermal study analysis pointed out the fact that geopolymer samples (Na_{1? x} Cs _x )‐GP, can be considered as solid solutions.     

Fertigung einer universellen Hüftprothesenpfanne mittels Hochdruckblechumformung

In recent years, the use of hip prostheses has become a routine procedure. The use of total hip replacement has evolved in recent years to a routine procedure. Despite this experience, it always comes back to complications. Especially the migration or loosening of the acetabular component because of the artificial load adaptive bone remodeling is still a current problem. This is due to the changing mechanical situation after the implantation of the prosthesis. Another problem is the high bone loss during implantation, which complicates a revision of the prosthesis. One solution is the use of patient‐specific prostheses. So far, the use of these prostheses is limited due to the time‐consuming and cost‐intensive production. The overall objective of the presented project in this publication is the development and establishment of an innovative concept for the production of patient‐specific hip prosthesis made of titanium plates by sheet metal forming. The idea of this concept involves the development of a two‐stage process. First of all a standardized hip prosthesis is made by high‐pressure sheet metal forming and then individually in the second step. This publication contains the derivation of the standard prosthesis. For this purpose, a design methodology was generated, based on the so‐called agglomerative clustering. In addition, presents the results of the numerical preliminary design of the first stage of the process and the tool developed concept in the course of this paper.     

Modeling bread baking with focus on overall deformation and local porosity evolution

A two dimensional model of bread baking was developed including, for the first time, the dependence of dough viscosity on both temperature and moisture content, the carbon dioxide dissolved from liquid water together with gas generation from yeast at the beginning of baking and the shrinkage due to dough drying. Particular attention was paid to experimental validation of both overall and local variables such as local temperature, overall mass loss, and local moisture content, overall CO₂ released into the oven, and overall deformation and local expansion or shrinkage. Sensitivity studies on generation of carbon dioxide, gravity, and shrinkage are presented to discuss their influences on bread geometry, porosity (reflecting the alveolar structure) and gas pressure. © 2016 American Institute of Chemical Engineers AIChE J, 62: 3847–3863, 2016     

Extraction and Characterization of Montmorency Sour Cherry (Prunus cerasus L.) Pit Oil

Montmorency sour cherry (Prunus cerasus L.) pit oil (CPO) was extracted and characterized by various methods including: GC, LC–MS, NMR, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and X‐ray powder diffraction (XRD). The oil gave an acid value of 1.45 mg KOH/g, saponification value of 193 mg KOH/g and unsaponifiable matter content of 0.72 %. The oil contained oleic (O) and linoleic (l ) acids as the major components with small concentrations of α‐eleostearic acid (El, 9Z,11E,13E‐octadecatrienoic acid) and saturated fatty acid palmitic (P) acid. The CPO contained six major triacyglycerols (TAG), OOO (16.83 %), OLO (16.64 %), LLO (13.20 %), OLP (7.25 %), OOP (6.49 %) and LElL (6.16 %) plus a number of other minor TAG. The TAG containing at least one saturated fatty acid constitute 33 % of the total. The polymorphic behavior of CPO as studied by DSC and XRD confirmed the presence of α, β′ and β crystal forms. The oxidative induction time of CPO was 30.3 min at 130 °C and the thermal decomposition temperature was 352 °C.     

BaTiO3 incorporation effect on the dielectric properties of polymer from aqueous emulsion: An enhanced dispersion technique

An economic and environment friendly process was adapted to synthesize new dielectric composite materials. Using ethylene vinyl acetate (EVA)/vinyl ester of versatic acid (VeoVa) terpolymer as an aqueous emulsion provides a homogenous dispersion of BaTiO₃ (BT) particles, due to the high viscosity and polarity of the vinyl resin (VR). Composites films were obtained from these dispersions by water evaporation. The evolution of the dielectric properties as a function of the BaTiO₃ content, was correctly fitted by a Maxwell‐Garnett model. This fitting of the experimental curve shows a good dispersion of filler in the vinyl resin and the particles separation by a layer of resin as expected for the preparation method used in this study. The VR/BT composites show good synergy between the dielectric properties of the different phases of the composites due to the formation of macrodipoles and to the strong interactions between polar EVA/VeoVa groups and the BaTiO₃ particles surface. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44333.